ID CODES REGISTRATION PROCEDURES



The ID codes necessary for the engine immobiliser system and the keyless entry system can be registered by operating on the M.U.T.-III screen.
caution
  • If the ignition key with transmitter is added or replaced, register the key (key ID), and then register the keyless ID again.
  • Do not register the ignition key registered for other vehicle.

SUPPLY UNIT LIST FOR INDIVIDUAL KEY
Ignition key (with transmitter)
Ignition key (without transmitter)





KEY SUPPLY UNIT LIST FOR OTHER THAN INDIVIDUAL KEY
Full service key set <vehicles with keyless entry system>
Full service key set <vehicles without keyless entry system>




Handle lock service key set <vehicles with keyless entry system>
Handle lock service key set <vehicles without keyless entry system>




Door service key set
Trunk lid service key set <vehicles without keyless entry system>
note It is the key that comes with the door service key set and the trunk lid service key set. It can only be used for locking and unlocking, and it cannot start the engine.







note
  • When re-registering the key (key ID and keyless ID), all the keys (key ID and keyless ID) registered before must be re-registered because all of them will be erased.
  • When the ignition key was replaced by the key set, register the key (key ID) using the bar code No. attached to the key.
  • If the registration fails, repeat from the start.
  • If the key registration cannot be performed, check the trouble symptom. (Refer to .)
  • After registering the keys, make sure that the engine is started normally with all of the keys registered.





Connect the M.U.T.-III to the 16-pin diagnosis connector as follows.
note For details on how to use the M.U.T.-III, refer to the "M.U.T.-III User’s Manual."
1.Start the M.U.T.-III system on the PC and turn the ignition switch to the "ON" position.
note Since the M.U.T.-III screen display changes according to the vehicle specifications, the illustrations for each item may differ from the actual screen display.
2.

Select "IMMOBI/KOS/Keyless" button from the "System Select" screen. Then, select the applicable option code item and push the OK button.

3.Select "Special Function" on the next screen.
4.

Select the button of the operation to be performed from the "Special Function" screen.

note For "Engine Key Code Reg. & Chassis No. Writing," refer to GROUP 00 - Precautions before Service .

KEY REGISTRATION METHOD


1.

When "Key registration" screen is displayed, enter the password for the key registration and press the OK button. Then, "Executing!" is displayed and the registration process starts.
note
  • If the wrong password is entered consecutively 5 times, the password entry for the key registration will be disabled for 16 minutes.
  • The key registration cannot be cancelled during the operation.
2.

When the key registration is completed, "Completed" is displayed. To register the next key, follow the message on the screen and press the OK button. Then, "Executing!" is displayed again and the registration process for the next key starts. To finish the key registration, press the cancel button.
note
  • In order to register another key consecutively after registering the first key, the ignition switch must be turned to the ON position with the second key within 30 seconds after turning it to the "LOCK" (OFF) position with the first key.
  • Up to eight keys can be registered.

KEY REGISTRATION (BARCODE NO.) METHOD


1.

When "Key Registration (Barcode No.)" screen is displayed, enter the password for the key registration and press the OK button.
note If the wrong password is entered consecutively 5 times, the password entry for the key registration will be disabled for 16 minutes.
2.


Follow the message on the screen to enter the bar code No., and then press the OK button.
3.When "Do you want to start registration?" is displayed, press the OK button to start the registration, or press the Cancel button to cancel the registration.
4."Key Registration was completed" is displayed. Press the OK button to finish the registration.

"KEYLESS ID REGISTRATON" METHOD


1.

On the "Keyless ID Registration" screen, enter the password and press the OK button.
2.Register within 1 minute and send the programming packet* to register the keyless ID. To register multiple keys, register the next key within 1 minute from the registration operation of previous key. Complete the registration of necessary keys, then press the OK button to finish the keyless ID registration.
note
  • Up to eight ignition keys can be registered.
  • *: Programming packet sending procedure
    Complete the following steps 1 to 3 within four seconds.

    1. Press and hold both the lock and the unlock switch for 1 second or longer.
    2. Release both the lock and the unlock switch for 0.5 second or longer.
    3. Press the unlock switch.
3.Push the OK button after "Keyless ID Registration was finished." is displayed.
4.

Check number of the keyless IDs registered.